Showing 25–35 of 35 results
-
$168.00Billet Trans Yoke
– AISI 4140 STEEL BILLET, FULLY MACHINED, AND THROUGH HARDENED
– CLEARANCED FOR UP TO 20° DRIVESHAFT YOKE ANGLE WHEN USED WITH STRANGE OVAL DRIVESHAFT YOKE
– DOES NOT HAVE TO BE USED WITH STRANGE OVAL DRIVESHAFT OR SLIP YOKES
– USES A 1310 U-JOINT (STRANGE OVAL USES A RE-GREASABLE 1310 U-JOINT)- PRECISE ALIGNED U-JOINT BORES MINIMIZES RUNOUT
– MODERATE INTERFERENCE FIT ON U-JOINT REDUCES OPERATING TEMPERATURE
-
$20.003/8″-24 Stage 8 Yoke Retaining Bolt Kit
– AISI 4140 STEEL BILLET, FULLY MACHINED, AND THROUGH HARDENED
– CLEARANCED FOR UP TO 20° DRIVESHAFT YOKE ANGLE WHEN USED WITH STRANGE OVAL DRIVESHAFT YOKE
– DOES NOT HAVE TO BE USED WITH STRANGE OVAL DRIVESHAFT (DKM203)
– USES A 1310 U-JOINT (STRANGE OVAL USES A RE-GREASABLE 1310 U-JOINT)
– PRECISE ALIGNED U-JOINT BORES MINIMIZES RUNOUT
– MODERATE INTERFERENCE FIT ON U-JOINT REDUCES OPERATING TEMPERATURE
-
$168.00Billet Quick Change Yoke
– AISI 4140 STEEL BILLET, FULLY MACHINED, AND THROUGH HARDENED
– CLEARANCED FOR UP TO 20° DRIVESHAFT YOKE ANGLE WHEN USED WITH STRANGE OVAL DRIVESHAFT YOKE
– DOES NOT HAVE TO BE USED WITH STRANGE OVAL DRIVESHAFT (DKM203)
– USES A 1310 U-JOINT (STRANGE OVAL USES A RE-GREASABLE 1310 U-JOINT)
– PRECISE ALIGNED U-JOINT BORES MINIMIZES RUNOUT
– MODERATE INTERFERENCE FIT ON U-JOINT REDUCES OPERATING TEMPERATURE
-
$261.00Forged Driveshaft Slip Yoke
– AISI 4140 STEEL BILLET, FULLY MACHINED, AND THROUGH HARDENED
– CLEARANCED FOR UP TO 20° DRIVESHAFT YOKE ANGLE WHEN USED WITH STRANGE OVAL DRIVESHAFT YOKE
– DOES NOT HAVE TO BE USED WITH STRANGE OVAL DRIVESHAFT (DKM203)
– USES A 1310 U-JOINT (STRANGE OVAL USES A RE-GREASABLE 1310 U-JOINT)
– PRECISE ALIGNED U-JOINT BORES MINIMIZES RUNOUT
– MODERATE INTERFERENCE FIT ON U-JOINT REDUCES OPERATING TEMPERATURE
-
$71.00U-Bolt Strap Kit
HEAT TREATED BILLET CHROMOLY STEEL STRAPS
– 65% TENSILE STRENGTH INCREASE OVER AN OEM U-BOLT
ETD150 STEEL STUDS
– 90% TENSILE STRENGTH INCREASE VERSES OEM U-BOLT
12 POINT DISTORTED THREAD LOCKING NUTS
– ENSURES FASTENERS REMAIN TIGHT AND U-JOINT REMAINS IN PLACE
CONSISTENT U-JOINT CLAMPING FORCE
-FULL 360 DEGREE SUPPORT OF U-JOINT BEARING CAP
-REDUCES OPERATING TEMPERATURE AND INCREASES LIFE
INADVERTENT OVER TORQUING WILL NOT RESULT IN BEARING JOURNAL
BRINELLING OR NEEDLE ROLLER DAMAGE
-
$34.001310 U-JOINT – Re-lube 5-153X
– RE-GREASABLE U-JOINT WITH STEEL SHIMS UNDER CAPS (NOT PLASTIC SHIMS)
– MANUFACTURED BY SPICER
-
$285.00NASCAR Pinion Yokes
• AISI/SAE 4340 nickel-chromium-molybdenum aircraft quality
steel is through hardened for optimized strength & toughness
• Extensive mill profiling & pocketing for lightweight rigid design
Integral doweled billet u-joint caps for precise located fit
• U-joint bores machined with caps in place promotes even
clamp load on u-joint
• Broached spline post heat treat provides precise, accurate
and consistent fit
• ARP 12 point cap bolts
• Cap bolt safety wire provisions -
$340.00Pinion Retainer DPC100
With a weight savings of up to 1 ¾ lbs. as compared to the standard “Daytona” cast iron pinion retainers, Strange Oval produces 2 variations of billet steel pinion retainers. While lighter in weight, our pinion retainers maintain a lower axial and radial deflection rate improvement of 20% over the cast iron counterpart. By reducing pinion deflection, the Strange Oval pinion retainers improve gear life
-
- Heat treated, fully machined, billet chromoly steel construction
-
- Improved rigidity and lighter weight than the popular daytona pinion retainer
-
- Nascar approved
- Iron shed (isp105) support available for enhanced gear mesh oiling
- Pinion Retainer # DPC100 (w/o external lubrication line attachment feature)
-
-
$380.00Pinion Retainer ISP105
With a weight savings of up to 1 ¾ lbs. as compared to the standard “Daytona” cast iron pinion retainers, Strange Oval produces 2 variations of billet steel pinion retainers. While lighter in weight, our pinion retainers maintain a lower axial and radial deflection rate improvement of 20% over the cast iron counterpart. By reducing pinion deflection, the Strange Oval pinion retainers improve gear life
-
- 4140 pre heat treated steel provides increased strength and stability over cast iron
-
- Precision bearing bore alignment and concentricity for better overall gear efficiency
-
- Has constant bearing spacing for easier and more accurate preload set up
-
- Has splash type lubrication features as well. Does not have to be pressure fed
-
- Front lube return provides several features
-
- Returns lube directly to gear mesh
-
- Allows for constant lubrication to pinion bearings
-
- Lube being returned to critical areas protects and allows a low lube condition
-
- Shortens the length of lubrication cooler lines
- Less likely to break front return fitting as to a exposed fitting on back of housing
- Pinion Retainer # ISP105 (with external lubrication line attachment feature)
-
-
$248.0032 Spline Gun-Drilled Driveshaft – Shaft Only
– WILL FIT MOST ALL MANUFACTURERS 32 SPLINE DRIVESHAFT SLIP YOKES
– 32 SPLINE DRIVESHAFT IS 14% TORSIONALLY STRONGER IN SPLINED AREA COMPARED TO 16 SPLINE SHAFT
– THROUGH HARDENED HY-TUF STEEL – EXCEPTIONAL SHOCK RESISTANCE AND TORSIONAL STRENGTH
– GUNDRILLED FOR WEIGHT REDUCTION
– TIMED SPLINES PROVIDES PROPER U-JOINT PHASING
– TIGHT RUNOUT CONTROL AND SPLINE CLEARANCE ELIMINATES VIBRATION
-
$20.00Torsion Bar Pre-Stressed Service
Re-stressing allows bars to have greater elastic twist angle and hence more wheel travel. It also drastically reduces bar settling eliminating a need for a racer to bounce a car up and down in order for it to settle at the correct height. During pre-stressing the bars are twisted within the plastic shear zone over a specific angle, unloaded and repeated two more times.
The Torsion bars’ strain curves are carefully monitored during the procedure. The procedure causes compressed residual stresses at the outer boundary of a bar increasing its yield strength. Ultimately, this saves time and, more importantly, conditions the bar for immediate on-track use in while also increasing the bars overall longevity.